Видео

Another quicker way surely would be to draw some lines at 3.6" on the target and see through the scope if the milldots correspond to the lines.

Same problem with my gen 2 25. Cal ordered mine from Amazon 🤦

Will this kill a raccoon

they will regulate air guns. it's already starting with the murders in Florida using air guns. and others in the mid-west.

Bought one recently. Wish I had seen this video! Exact same issue. Piss poor accuracy. Some ammo is just plain ridiculous...four inch groups at 50? I have noticed that light pressure downward on the bolt while shooting greatly reduces group size. I'm a right handed shooter...so I use my left hand under the chassis and hold the bolt with my fingers...gonna sell it

Wouldn't lead pellets be double damage which leads to lead poisoning and a hole of fragments

Too funny, communist states. They are all republic states with democratic elected collective authority.

This gave me a couple ideas to look into on my ruger american 22mag. Looks about the same bolt. Either way subscribed 👏

Thanks for sharing!!

I would think that as long as the bolt probe is centered in the barrel that having the Pellets engage the rifling would be a positive, but don't understand how the port is in the rifling? That sounds messed up and would need to see pictures. I reload and you get the best accuracy and consistent velocity if the bullets engage the rifling but people don't do this because it is dangerous as you get a pressure spike. All that matters is that your rifle shoots accurate in the end. My .25 G2 shoots sub MOA out to 70yrds and about 1.3 MOA at 100yrds with JSB 33gr jumbos. I have ported it now, put in adj. hammer spring, barrel band, and have an adjustable regulator for 1700 - 2700.... I just ordered a .22 cal to use the tank off that for the new regulator on my .25 and the .25 (2100psi) regulator on the new .22 for heavy slugs. If you want power you can't beat the G2 at its price.

What a load of bologna. 😂

Thanks

They should of never used the 10/22 mags for that gun, they should made RPR own proprietary magazines. If you want to match, shoot it, you have to spend the money to make it shoot better, I own one!

I wonder what the 25 cal what have done at a more normal 850 880 fps.

Blowback action has nothing to do with a vacuum created when the bullet exits the barrel.

I hunt rats on my families property and i have two i use , a full auto 600 fps model of the mp 40 exact weight and same fire weight and looks identical to the real thing and i got a 1250 fps break action pellet rifle , alot of people dont believe me when i tell them the 600fps bb gun works perfectly for big rats , as long as you hit neck head or lungs or heart its dead within 30 seconds , the lungs are what i go for usually with the bb gun cause it will go straight through and through with a steel bb at 600 fps and at full auto im able to hit multiple rats at once and i have it set up so they have to come outside to the back deck to get the bait i use which is just cat food and so sometimes there will be 10 of em at once and i can spray them down not worrying much about my shot placement and ill end or injure most of them and the injured ones i usually find the next day in the house or in the front of the property or behind the house

Theres bean bag guns now adays that are lethal if shot at the lungs. Therea videos of police shooting prisoners with beanbags and the beanbags going through the ribs into the lungs and causing the death of the prisoners

A tin of spam is not a pig jaw

WTH all you did was say you used a pen tube. You didn't explain how or show how you used it. How are we supposed to know what to do with the pen? Useless stupid video.

i had two element helix that has bad parallax adjustment, when you torque the rings more than 10 inch pounds, the parallax sticks and does not focus on the yardage marks. i think it has so thin tube that the parallax is affected by the torque of the rings. dont have this problem with my element titan, vortex venom, aztec emerald and discovery scopes.

.25 for self defense? Nah , man the .58 cal Megladon with 15inch barrel that is self / home defense. If you need something a bit more compact then go with the T9 in .357 but .25 cal is not a self defense gun.

The music sucks!!!!

my 201 is great!

Just wanted to offer you information. I too have searched for a solution to this problem. In the end your idea kinda works...but this is my findings. The issue is that the bolt rotates too far to the right and is not level or faced propperly...the problem is all in the firing pin. The rear is sharp. It holds on spring and rotates bolt. Fix... clean up rear of firing pin and polish. It doesn't have to be flat just smooth. No burrs. Also polish spring ends with 1500 grit paper. Lube and reassemble. Bolt then uses guide intended to keep it straight and level. foot note giving you credit in pointing out problem. It prompted me to dig deeper. Thank you.

Just curious why you still sell the supposed junk compressors in your Amazon store???

"A fried bologna samich with mayo and a pellet"...

Nice and thorough review

None of those magazines should "Wiggle" The BX-15 and BX-25 magazines are shorter in length. Bad manufacturing and engineering issues. Nothing more. Should never have been made like that. You should send them this video as evidence and what the problem is.

Thank you. Just discovered this problem. My fist shots were constantly turning my 1/4” groups in 3/4” groups.

All compressors will fail eventually as heat and water are constantly produced. Water inside the compressor between stages will corrode check valves, sealing surfaces and lines. All air contains water vapor, compressing it causes it to condense which causes damage to both compressor and anything using it. I feed my Spirtech with ultra dry air from a 120 PSI storage tank half full of desiccant. A regulator drops pressure to 5 PSI which then goes to the inlet hose. I modified the inlet filter with a brass tube fitting. It makes fills a bit more complex but zero moisture in the equipment.

Your video was well done. Thank u.

What a waste of food smh

I've got a racoon problem and I am glad I watched your video . I have no dault my 177 will do the trick in getting rid of them . thank you for showing your video

Do a video on using a shaft collar as a barrel harmonic tuner (aka $2 barrel tuner; YT video title).

Love your videos. Your video are not a dog & panty show, you just get to your testing facts.

I replaced the bolt handle with an Anarchy Outdoors bolt handle took care of my issue.

Thanks you just saved me a ton, called Ruger same issue on my 17 HMR, they are gonna replace the bolt under warranty this is on. 2024 BUILD

A low budget scope....12.00 bucks these days ... but on my $285 dollar Ruger 10-22 , its terrific. Thanks for that very fair review.

I was thinking instead of using a piece of zip tie why don’t you solder something more permanent and attach a piece of blued metal so that it holds permanently instead of just gluing a piece of zip tie. Soldering on a small piece of blue metal would be a more reliable backstop to prevent your bolt from going any further than where you want it to be.

Mine went to crap on mw this morning. It was great for the last few years and today it took a dump. I've cleaned it, made sure everything was tight and the groups just stayed open. I'm bout to surrender. Thanks again for breaking it down J!

He keeps saying CCI stinger- when it’s actually the standard velocity

Smaller is better that’s what Iv been trying to tell my wife for years 😂

Excellent information and presentation of said info. Thank you for telling it like it is and not fluffing things up. I've just recently started watching your channel. I have never shot competition. I shoot targets and squirrel. But things you discuss do match what I have experienced as a common shooter with a few different rifles and I'm like wow. Didn't ever think of that. And I liked your barrel cleaning and 15 shot vidoes. Great channel! Thank you.

good video glad i did not purchase this rifle ....

Thank you 👍

I've got a kidd barrel on my 10/22. now, the factory barrels chamber was oversized, the fired cases were all blackened, showing cases where not obturating correctly

Gracias

I am not pulling your chain but you have the most accurate air gun videos I've ever seen they're very educational and truly depict the capability of these weapons even though they seem minuscule compared to firearms you did a great job man keep it up

Working on implementing the suggestions on my gun but I found that the washer dimensions you gave didnt fit my gun. I found a diameter of 18.8mm and internal diameter of 9mm to fit best with no slop. The smaller diameter wouldnt center in the shroud and the increased internal made it less likely to protrude into the path of the pellet. I went with a 1.6mm thickness. All this was 3d printed since its just a spacer

Well return it and let them know that and get another one yeah all the Vp come in boxes or go with a smaller place like Utah or pellet stop